Dispatched in 3–4 working days
Everything on this page is fabricated, blasted, coated and off our loading bay within 3–4 working days of the order being confirmed. It is all made to order in Doncaster — these are not stocked imports, and comparable fabricated items are commonly quoted at one to six weeks elsewhere.
31 products
Bollards & Impact Protection
Fixed Flat Top Bollard
Fabricated in our Doncaster workshop from CHS with a fully welded flat cap plate and a sealed root section for direct concrete setting. Cut, welded and finished in-house. 168mm CHS, 5mm wall Fully welded flat cap plate Root-set, 500mm below ground Hot dip galvanised to BS EN ISO 1461 as standard Powder coat to any RAL on request Made to order — dispatched in 3–4 working days. Galvanised finishes 7–10 working days.
£56.50 ex VAT
Bollards & Impact Protection
Fixed Mitre Top Bollard
Angled mitre-cut head with a welded closing plate — sheds water and reads as a more considered detail on public realm schemes. Fabricated start to finish on Bentley Road. 168mm CHS, 5mm wall 45° mitre head, fully welded and dressed Root-set, 500mm below ground Galvanised to BS EN ISO 1461, powder coat optional Made to order — dispatched in 3–4 working days.
£58.50 ex VAT
Bollards & Impact Protection
Base Plated Bollard
Surface-fixed bollard on a welded and drilled base plate — no excavation, bolts straight to a slab or existing hardstanding. Ideal for retrofit protection in car parks and yards. 168mm CHS on 250 x 250 x 10mm plate Four 18mm fixing holes, gussets welded to the shaft Supplied with resin anchor set Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£59.50 ex VAT
Bollards & Impact Protection
Single Waisted Bollard
Traditional waisted profile with a domed head, fabricated from tube and plate rather than cast — lighter, cheaper to freight and easier to replace after impact. Waisted collar detail, welded and dressed smooth Semi-dome head plate Root-set or base plated on request Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£78.50 ex VAT
Bollards & Impact Protection
Removable Lock-Down Bollard
Lifts out of a flush ground socket and locks down with an integral padlock housing. Fabricated with a machined spigot so it drops in cleanly rather than fighting the socket. 114mm or 168mm CHS shaft Flush galvanised ground socket with drainage and lid Integral padlock shroud, padlock not supplied Lifting handle welded to the head Made to order — dispatched in 3–4 working days.
£124.50 ex VAT
Bollards & Impact Protection
Fold Down Bollard
Hinged at the base so it drops flat to the ground and locks upright — the right answer where a removable bollard would get lost. Hinge pin and lock housing fabricated and fitted in-house. Heavy hinge block welded to a bolt-down base Locks in the upright position, padlock shroud included Rubber buffer on the fold-down face Galvanised, powder coat optional Made to order — dispatched in 3–4 working days.
£136.50 ex VAT
Car Park & Warehouse Protection
Column & Corner Protector
Wrap-around steel guard for warehouse racking legs, portal frame columns and building corners. Rolled, welded and coated in-house in high-visibility yellow or any RAL. 6mm plate, radiused corners Bolt-down feet, resin anchors supplied Yellow RAL 1023 as standard Made to order — dispatched in 3–4 working days.
£96.00 ex VAT
Car Park & Warehouse Protection
Pedestrian Guardrail Panel
Welded infill guardrail for footways, school gates and car park edges. Panels and posts are made here, so non-standard bay widths and raking runs cost no more than the catalogue sizes. 1000mm high above ground Vertical infill at 100mm centres Root-set or base-plated posts Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£118.00 ex VAT
Car Park & Warehouse Protection
Hoop Barrier
Simple bent-tube hoop for protecting doorways, dock edges and pedestrian routes. Bent and welded from one length so there is no joint at the crown. 60mm or 76mm CHS Root-set or bolt-down feet Yellow RAL 1023 or galvanised Made to order — dispatched in 3–4 working days.
£84.00 ex VAT
Car Park & Warehouse Protection
Armco-Style Post & Rail Bay
Fabricated posts, cleats and end terminals for crash rail runs in yards and warehouses. We make the posts and fixings; the rail section itself is bought in as a material. Fabricated SHS posts with welded rail cleats Single or double rail height End terminal wraps included Galvanised finish Made to order — dispatched in 3–4 working days.
£156.00 ex VAT
Car Park & Warehouse Protection
Wheel Stop
Fabricated steel wheel stop with welded end caps and countersunk fixing points — outlasts the moulded rubber versions in a working yard. Folded 5mm plate, welded ends Two fixing points, anchors supplied Yellow RAL 1023 or galvanised Made to order — dispatched in 3–4 working days.
£72.00 ex VAT
Car Park & Warehouse Protection
Bump Rail & Wall Protection
Wall-mounted impact rail on fabricated stand-off brackets, keeping forklifts and pallet trucks off blockwork and cladding rails. Rail on welded stand-off brackets Supplied in 2.0m or 3.0m lengths Yellow RAL 1023 or galvanised Made to order — dispatched in 3–4 working days.
£118.00 ex VAT
Car Park & Warehouse Protection
Trolley Bay Frame
Welded trolley bay frame with a header rail for signage, made to the bay width you actually have rather than a standard module. SHS frame with welded corner gussets Header rail drilled for a sign panel Root-set or base-plated Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£985.00 ex VAT
Site & Street Metalwork
Cycle Stand — Sheffield Hoop
Bent-tube Sheffield stand with an optional tapping rail, root-set or base plated. Bent from a single length in our own workshop. 48mm or 60mm CHS Root-set or bolt-down base plates Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£78.00 ex VAT
CCTV Poles & Columns
Camera Mounting Bracket
Fabricated mounting brackets for pole, wall and corner installations, drilled to the fixing centres of your camera or enclosure rather than a generic pattern. 6mm plate, fully welded gussets Cable pass-through with a grommet Drilled to your template — send the datasheet Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£68.00 ex VAT
CCTV Poles & Columns
Column Base Plate & Foundation Cage
Holding-down bolt cage and template for flange-mounted columns, made to your bolt centres so the column lands square first time. M16 or M20 holding-down bolts with plate washers Welded cage with a setting-out template Galvanised throughout Made to order — dispatched in 3–4 working days.
£96.00 ex VAT
Intercom & Reader Posts
Single Intercom Post
Steel intercom pedestal with a rear access panel and a clean cable route from the root to the device aperture. We supply the post — the electronics come from your own supplier. 150 x 150mm SHS, welded cap Lockable rear access panel Cable entry at the root, sealed grommet Supplied undrilled, or cut to your unit's template Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£195.00 ex VAT
Intercom & Reader Posts
Twin Height Intercom Post
Two apertures at car and HGV driver height on one post, so a single pedestal serves both. Apertures cut to your device footprints before coating. 150 x 150mm SHS Two device apertures, heights to your spec Full-height rear access panel Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£298.00 ex VAT
Intercom & Reader Posts
Card Reader Post
Slim pedestal for proximity and keypad readers, with an angled head face so the reader sits square to the driver's window. 100 x 100mm SHS Angled head plate, aperture to your reader Rear access panel and cable grommet Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£168.00 ex VAT
Intercom & Reader Posts
Combination Intercom & Reader Post
One post carrying an intercom, a reader and, where needed, a keypad — apertures set out on a drawing you approve before we cut. 150 x 150mm SHS Up to three device apertures Full-height rear access panel Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£312.00 ex VAT
Farm & Field Gates
Gate Furniture Set
Fabricated gate ironmongery — spring bolt kits, adjustable gate eyes and wall plates, all made and galvanised in-house. Spring bolt kit with keeper Adjustable gate eyes, threaded Wall plate with fixings Hot dip galvanised Made to order — dispatched in 3–4 working days.
£32.00 ex VAT
Estate Fencing & Tree Protection
Estate Railing Panel
Traditional estate railing with through-drilled horizontal rails and pointed verticals, welded and finished here. Rakes and curves are made to the survey, not bent on site. Pointed vertical bars through horizontal rails Standard heights 900mm and 1200mm Root-set or base-plated posts Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£148.00 ex VAT
Estate Fencing & Tree Protection
Tree Guard
Welded tree guard for street and car park planting, bolted in halves so it can be fitted around an established stem and removed later without cutting. Two-part bolted construction Vertical bars at 100mm centres Root-set legs Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£268.00 ex VAT
Domestic Steel Gates
Steel Pedestrian Gate — Bow Top
Bow top pedestrian gate to match a railing run, with a self-closing hinge option for school and play area boundaries. Welded frame, bow top infill, no finger traps Self-closing hinge option Galvanised and powder coated to any RAL Made to order — dispatched in 3–4 working days.
£285.00 ex VAT
Commercial Gates
Gate Posts & Drop Bolt Set
Fabricated hanging and closing posts with welded hinge lugs, plus a drop bolt and ground receiver. Sized to the leaf weight rather than a catalogue default. Heavy SHS posts, welded hinge lugs Drop bolt with a galvanised ground receiver Root-set or base-plated Galvanised finish Made to order — dispatched in 3–4 working days.
£385.00 ex VAT
Railings & Balustrade
Vertical Bar Railing Panel
Welded vertical bar railing for boundaries and plant enclosures, made in bay widths to suit the run rather than forcing standard modules onto site. Vertical bars through horizontal rails Standard heights 1200mm and 1800mm Root-set or base-plated posts Galvanised and powder coated Made to order — dispatched in 3–4 working days.
£158.00 ex VAT
Railings & Balustrade
Bow Top Railing Panel
Bow top railing with no finger traps or foot holds — the standard answer for schools, play areas and housing schemes. Looped bow top heads, welded frame Standard heights 1000mm and 1200mm Root-set or base-plated posts Galvanised and powder coated to any RAL Made to order — dispatched in 3–4 working days.
£142.00 ex VAT
Railings & Balustrade
Wall-Mounted Handrail
Tubular handrail on welded stand-off brackets, with returns to the wall at both ends. Supplied in fabricated lengths to your setting out. 42mm CHS with welded returns Stand-off brackets at 1.0m centres Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£118.00 ex VAT
Covers & Frames
Duct & Trench Cover
Fabricated cover and frame for service ducts and trenches, in chequer plate or open grating, with lifting keys supplied. Chequer plate or open grating infill Welded angle frame, cast-in lugs Lifting key set included Galvanised finish Made to order — dispatched in 3–4 working days.
£185.00 ex VAT
Access & Safety Metalwork
Mezzanine Edge Protection
Bolt-down edge protection for mezzanines and loading edges, with a knee rail and toe board as standard. Posts, top rail, knee rail and toe board Bolt-down base plates Supplied in 1.5m or 2.0m bays Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£148.00 ex VAT
Access & Safety Metalwork
Machine & Plant Guarding
Bolt-together mesh guarding panels and posts for machinery and robot cells, with hinged or sliding access doors and interlock mounting plates. Welded frames with mesh infill Hinged or sliding access door option Interlock switch mounting plates Powder coated to any RAL Made to order — dispatched in 3–4 working days.
£168.00 ex VAT
Need dispatched in 3–4 working days to your own sizes?
Send a drawing or a schedule and we'll price it against your spec — budget costs back within 48 hours.