Steelwork for industrial and manufacturing sites
Machine guarding to your equipment footprint, column and rack protection, walkways, caged ladders and structural fabrication — measured on site, made in Doncaster, and fitted by our own team out of hours where production cannot stop.
33 products
Bollards & Impact Protection
Fixed Flat Top Bollard
Fabricated in our Doncaster workshop from CHS with a fully welded flat cap plate and a sealed root section for direct concrete setting. Cut, welded and finished in-house. 168mm CHS, 5mm wall Fully welded flat cap plate Root-set, 500mm below ground Hot dip galvanised to BS EN ISO 1461 as standard Powder coat to any RAL on request Made to order — dispatched in 3–4 working days. Galvanised finishes 7–10 working days.
£56.50 ex VAT
Bollards & Impact Protection
Base Plated Bollard
Surface-fixed bollard on a welded and drilled base plate — no excavation, bolts straight to a slab or existing hardstanding. Ideal for retrofit protection in car parks and yards. 168mm CHS on 250 x 250 x 10mm plate Four 18mm fixing holes, gussets welded to the shaft Supplied with resin anchor set Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£59.50 ex VAT
Bollards & Impact Protection
Removable Lock-Down Bollard
Lifts out of a flush ground socket and locks down with an integral padlock housing. Fabricated with a machined spigot so it drops in cleanly rather than fighting the socket. 114mm or 168mm CHS shaft Flush galvanised ground socket with drainage and lid Integral padlock shroud, padlock not supplied Lifting handle welded to the head Made to order — dispatched in 3–4 working days.
£124.50 ex VAT
Bollards & Impact Protection
Fold Down Bollard
Hinged at the base so it drops flat to the ground and locks upright — the right answer where a removable bollard would get lost. Hinge pin and lock housing fabricated and fitted in-house. Heavy hinge block welded to a bolt-down base Locks in the upright position, padlock shroud included Rubber buffer on the fold-down face Galvanised, powder coat optional Made to order — dispatched in 3–4 working days.
£136.50 ex VAT
Bollards & Impact Protection
Telescopic Bollard
Retracts into its own below-ground sleeve and locks at full height or flush. Sleeve, shaft and lock plate all fabricated here so tolerances are ours to control. Telescoping shaft in a sealed ground sleeve Locks up and locks down Drainage port in the sleeve base Galvanised throughout Made to order — dispatched in 7–10 working days (galvanising turnaround).
£268.00 ex VAT
Bollards & Impact Protection
Anti-Ram Security Bollard
Heavy-wall section on a deep root with a reinforced base cage, specified where the bollard has a real job to do rather than a visual one. Foundation detail supplied with the order. 168mm or 219mm CHS, 8mm wall Reinforcing bar cage welded to the root 1000mm foundation depth recommended Galvanised, RAL powder coat optional Made to order — dispatched in 7–10 working days.
£142.50 ex VAT
Car Park & Warehouse Protection
Column & Corner Protector
Wrap-around steel guard for warehouse racking legs, portal frame columns and building corners. Rolled, welded and coated in-house in high-visibility yellow or any RAL. 6mm plate, radiused corners Bolt-down feet, resin anchors supplied Yellow RAL 1023 as standard Made to order — dispatched in 3–4 working days.
£96.00 ex VAT
Car Park & Warehouse Protection
Hoop Barrier
Simple bent-tube hoop for protecting doorways, dock edges and pedestrian routes. Bent and welded from one length so there is no joint at the crown. 60mm or 76mm CHS Root-set or bolt-down feet Yellow RAL 1023 or galvanised Made to order — dispatched in 3–4 working days.
£84.00 ex VAT
Car Park & Warehouse Protection
Armco-Style Post & Rail Bay
Fabricated posts, cleats and end terminals for crash rail runs in yards and warehouses. We make the posts and fixings; the rail section itself is bought in as a material. Fabricated SHS posts with welded rail cleats Single or double rail height End terminal wraps included Galvanised finish Made to order — dispatched in 3–4 working days.
£156.00 ex VAT
Car Park & Warehouse Protection
Wheel Stop
Fabricated steel wheel stop with welded end caps and countersunk fixing points — outlasts the moulded rubber versions in a working yard. Folded 5mm plate, welded ends Two fixing points, anchors supplied Yellow RAL 1023 or galvanised Made to order — dispatched in 3–4 working days.
£72.00 ex VAT
Car Park & Warehouse Protection
Bump Rail & Wall Protection
Wall-mounted impact rail on fabricated stand-off brackets, keeping forklifts and pallet trucks off blockwork and cladding rails. Rail on welded stand-off brackets Supplied in 2.0m or 3.0m lengths Yellow RAL 1023 or galvanised Made to order — dispatched in 3–4 working days.
£118.00 ex VAT
Car Park & Warehouse Protection
Trolley Bay Frame
Welded trolley bay frame with a header rail for signage, made to the bay width you actually have rather than a standard module. SHS frame with welded corner gussets Header rail drilled for a sign panel Root-set or base-plated Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£985.00 ex VAT
CCTV Poles & Columns
Tubular CCTV Pole
Fabricated CCTV column with a welded cap plate, internal cable route and a lockable access door at low level. Cut, welded, blasted and coated in our Doncaster workshop — nothing subcontracted. 114mm to 168mm CHS depending on height Lockable cable access door with a welded reinforcing frame Internal earth stud and cable cleat Root-mounted or flange-mounted on a drilled base plate Galvanised to BS EN ISO 1461, RAL powder coat optional Made to order — dispatched in 7–10 working days. Drilled to your camera bracket pattern at no extra cost.
£285.00 ex VAT
CCTV Poles & Columns
Square Section CCTV Pole
Square hollow section column — flat faces make bracket and enclosure mounting far easier than a round pole, and it reads cleaner on modern buildings. 100mm to 150mm SHS depending on height Lockable cable access door, welded reinforcing frame Welded cap plate and internal earth stud Drilled to your bracket pattern on request Galvanised, RAL powder coat optional Made to order — dispatched in 7–10 working days.
£295.00 ex VAT
Intercom & Reader Posts
Card Reader Post
Slim pedestal for proximity and keypad readers, with an angled head face so the reader sits square to the driver's window. 100 x 100mm SHS Angled head plate, aperture to your reader Rear access panel and cable grommet Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£168.00 ex VAT
Commercial Gates
Cantilever Sliding Gate
Cantilever gate on a fabricated track beam — no ground track across the opening, so it works on sites that get mud, ice and heavy plant. Frame, beam, roller carriages and posts all made here. Cantilever beam sized to the clear opening Roller carriage posts with adjustable bearings Infill: vertical bar, welded mesh, palisade or sheet Prepped for automation on request Galvanised and powder coated to any RAL Prices shown are from-prices for standard clear openings. Anything non-standard, raked or automated is priced from your drawing — use the bespoke route and we will come back within 48 hours.
£3,450.00 ex VAT
Commercial Gates
Tracked Sliding Gate
Ground-tracked sliding gate for level, well-drained openings — lighter and cheaper than a cantilever where the ground conditions allow it. Welded frame on bogie wheels Track, guide posts and end stop included Infill to your specification Galvanised and powder coated From-price for the listed clear opening. Bespoke sizes priced from drawing within 48 hours.
£2,685.00 ex VAT
Commercial Gates
Bi-Fold Speed Gate Frame
Folding leaf sets for openings that need a fast cycle in a short run-back. Frames, pivot posts and folding hardware fabricated here; automation supplied and commissioned as a service. Two-leaf folding sets per side Heavy pivot posts with greased bearings Prepped for automation as standard Galvanised and powder coated From-price for the listed clear opening. Automation quoted separately.
£4,285.00 ex VAT
Commercial Gates
Swing Gate Prepared for Automation
Swing gate built from the outset to take a motor — reinforced stiles, welded motor mounting plates, pre-cut ducting entries and a bonded earth path. Retro-fitting automation to a gate that was not designed for it is where most installs go wrong. Reinforced hanging stiles and hinge posts Welded motor plates set out to your operator Ducting entries cut and sleeved before coating Earth bonding points welded in Galvanised and powder coated Made to order — dispatched in 7–10 working days. Automation supplied and commissioned as a fitted service — call for prices, trade discounts available.
£1,685.00 ex VAT
Mesh Gates
Mesh Infill Gate — Single Leaf
Single leaf gate with a welded steel frame and mesh infill to match an existing fence line. We fabricate the frame, posts and hardware; the mesh panel is bought in as a material. Welded box frame, mesh clamped and bolted Twin-wire or 358 high-security infill Adjustable hinges and lock box Galvanised and powder coated Made to order — dispatched in 7–10 working days.
£385.00 ex VAT
Mesh Gates
Mesh Infill Gate — Double Leaf
Double leaf vehicle gate with mesh infill, braced frames and a centre drop bolt, matched to twin-wire or 358 fence lines. Braced welded frames, bolted mesh infill Centre drop bolt and ground receiver Heavy hinge posts included Galvanised and powder coated Made to order — dispatched in 7–10 working days.
£1,485.00 ex VAT
Railings & Balustrade
Vertical Bar Railing Panel
Welded vertical bar railing for boundaries and plant enclosures, made in bay widths to suit the run rather than forcing standard modules onto site. Vertical bars through horizontal rails Standard heights 1200mm and 1800mm Root-set or base-plated posts Galvanised and powder coated Made to order — dispatched in 3–4 working days.
£158.00 ex VAT
Railings & Balustrade
Stair & Landing Balustrade
Balustrade to the rake of your stair, fabricated from a site survey so the panels land on the string without packing or bodging. Raked panels fabricated to survey Vertical bar or perforated sheet infill Fixed to string or landing edge Galvanised and powder coated Made to order — dispatched in 7–10 working days from approved survey.
£225.00 ex VAT
Site & Street Metalwork
Louvred Plant Screen
Louvred screening for condensers, generators and roof plant — fabricated frames with fixed blade louvres set to the free area the M&E spec calls for. Welded frame with fixed blade louvres Free area to your specification Access door option Galvanised and powder coated to any RAL Made to order — dispatched in 7–10 working days.
£685.00 ex VAT
Covers & Frames
Duct & Trench Cover
Fabricated cover and frame for service ducts and trenches, in chequer plate or open grating, with lifting keys supplied. Chequer plate or open grating infill Welded angle frame, cast-in lugs Lifting key set included Galvanised finish Made to order — dispatched in 3–4 working days.
£185.00 ex VAT
Access & Safety Metalwork
Mezzanine Edge Protection
Bolt-down edge protection for mezzanines and loading edges, with a knee rail and toe board as standard. Posts, top rail, knee rail and toe board Bolt-down base plates Supplied in 1.5m or 2.0m bays Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£148.00 ex VAT
Access & Safety Metalwork
Straight Flight Steel Staircase
Steel stair with welded stringers, treads and a landing, fabricated to the rise and going measured on site. Handrail and balustrade supplied to match. Welded stringers, chequer plate or open grating treads Landing frame included Fabricated from site survey Galvanised and powder coated From-price for the listed rise. Priced properly from your survey within 48 hours.
£1,685.00 ex VAT
Access & Safety Metalwork
Vertical Ladder & Safety Cage
Fixed vertical access ladder with a hooped safety cage and welded wall stand-offs, made to the climb height you give us. Welded stringers and round rungs Hooped safety cage above 2.5m Wall stand-off brackets included Galvanised finish Made to order — dispatched in 7–10 working days.
£685.00 ex VAT
Access & Safety Metalwork
Walkway & Gantry Section
Open grating walkway on a fabricated support frame with handrail both sides — supplied in sections sized for the lift available on site. Open grating deck on a welded frame Handrail, knee rail and toe board Bolted section joints Galvanised finish Made to order — dispatched in 7–10 working days.
£985.00 ex VAT
Access & Safety Metalwork
Machine & Plant Guarding
Bolt-together mesh guarding panels and posts for machinery and robot cells, with hinged or sliding access doors and interlock mounting plates. Welded frames with mesh infill Hinged or sliding access door option Interlock switch mounting plates Powder coated to any RAL Made to order — dispatched in 3–4 working days.
£168.00 ex VAT
Structural Fabrication
Fabricated Frames, Brackets & Support Steelwork
One-off frames, brackets, base plates, cleats and support steelwork made from your drawing or a sketch. This is the everyday work of the shop. Cut, drilled and welded to your drawing Section, plate and tube in stock or ordered to spec Blasted and coated in-house Supply only or supply and install Priced from your drawing. The listed price is a nominal booking value — send drawings through the bespoke route for a real figure within 48 hours.
£125.00 ex VAT
Finishing Services
Trade Shot Blasting & Powder Coating
Blast and coat for other fabricators, engineers and installers. Bring us your steel and it comes back blasted, primed if required and coated to any RAL. Shot blasting to SA2.5 Solvent-free powder coating, full RAL range Texture, hammer and metallic finishes Zinc-rich primer for exterior corrosion resistance Typical coating turnaround seven days Priced by area and component size. The listed price is a nominal booking value — send a component list for a proper quote.
£95.00 ex VAT
Finishing Services
Site Welding & Steelwork Repairs
Mobile welding and repair for gates, railings, plant and access steelwork — damaged hinge posts, sheared brackets, failed welds and impact damage. MIG, MMA and TIG on site Repair, re-hang and re-align Touch-in coating after repair Doncaster and surrounding area Priced on attendance. The listed price is a nominal booking value — call to confirm scope and timing.
£295.00 ex VAT
Need for industrial & manufacturing to your own sizes?
Send a drawing or a schedule and we'll price it against your spec — budget costs back within 48 hours.