Public realm steelwork for local authorities
Bollards, cycle stands, planters, tree guards, estate railing and bin stores RAL matched to your borough palette. Replacement items can be remade from a photograph so a damaged run stays consistent, and anti-tamper fixings are available throughout.
20 products
Bollards & Impact Protection
Fixed Flat Top Bollard
Fabricated in our Doncaster workshop from CHS with a fully welded flat cap plate and a sealed root section for direct concrete setting. Cut, welded and finished in-house. 168mm CHS, 5mm wall Fully welded flat cap plate Root-set, 500mm below ground Hot dip galvanised to BS EN ISO 1461 as standard Powder coat to any RAL on request Made to order — dispatched in 3–4 working days. Galvanised finishes 7–10 working days.
£56.50 ex VAT
Bollards & Impact Protection
Fixed Mitre Top Bollard
Angled mitre-cut head with a welded closing plate — sheds water and reads as a more considered detail on public realm schemes. Fabricated start to finish on Bentley Road. 168mm CHS, 5mm wall 45° mitre head, fully welded and dressed Root-set, 500mm below ground Galvanised to BS EN ISO 1461, powder coat optional Made to order — dispatched in 3–4 working days.
£58.50 ex VAT
Bollards & Impact Protection
Single Waisted Bollard
Traditional waisted profile with a domed head, fabricated from tube and plate rather than cast — lighter, cheaper to freight and easier to replace after impact. Waisted collar detail, welded and dressed smooth Semi-dome head plate Root-set or base plated on request Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£78.50 ex VAT
Bollards & Impact Protection
Removable Lock-Down Bollard
Lifts out of a flush ground socket and locks down with an integral padlock housing. Fabricated with a machined spigot so it drops in cleanly rather than fighting the socket. 114mm or 168mm CHS shaft Flush galvanised ground socket with drainage and lid Integral padlock shroud, padlock not supplied Lifting handle welded to the head Made to order — dispatched in 3–4 working days.
£124.50 ex VAT
Height Restriction Barriers
Fixed Goalpost Height Restriction Barrier
Welded goalpost frame with a signage plate mount on the crossbeam, set into concrete uprights. Clear height is fixed at fabrication so there is nothing to adjust or vandalise. SHS uprights with welded base cleats or root fixing Crossbeam with pre-drilled signage plate mount Clear height 2.1m standard, others on request Galvanised, RAL powder coat optional Made to order — dispatched in 7–10 working days.
£695.00 ex VAT
Height Restriction Barriers
Swing-Open Height Restriction Barrier
Goalpost barrier with a hinged crossbeam so authorised vehicles can be let through without dismantling anything. Hinge and locking post fabricated as one assembly. Hinged crossbeam on a greased pin Locking receiver post with padlock shroud Signage plate mount included Galvanised finish Made to order — dispatched in 7–10 working days.
£985.00 ex VAT
Height Restriction Barriers
Height-Adjustable Restriction Barrier
Telescoping uprights let the clear height be set on site and pinned, which suits car parks that change use or need a trial height before it is fixed. Pinned telescopic uprights, 1.8m to 2.5m clear Crossbeam with signage plate mount Locking pin set supplied Galvanised finish Made to order — dispatched in 7–10 working days.
£1,145.00 ex VAT
Car Park & Warehouse Protection
Pedestrian Guardrail Panel
Welded infill guardrail for footways, school gates and car park edges. Panels and posts are made here, so non-standard bay widths and raking runs cost no more than the catalogue sizes. 1000mm high above ground Vertical infill at 100mm centres Root-set or base-plated posts Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£118.00 ex VAT
Car Park & Warehouse Protection
Trolley Bay Frame
Welded trolley bay frame with a header rail for signage, made to the bay width you actually have rather than a standard module. SHS frame with welded corner gussets Header rail drilled for a sign panel Root-set or base-plated Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£985.00 ex VAT
Site & Street Metalwork
Cycle Stand — Sheffield Hoop
Bent-tube Sheffield stand with an optional tapping rail, root-set or base plated. Bent from a single length in our own workshop. 48mm or 60mm CHS Root-set or bolt-down base plates Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£78.00 ex VAT
CCTV Poles & Columns
Tubular CCTV Pole
Fabricated CCTV column with a welded cap plate, internal cable route and a lockable access door at low level. Cut, welded, blasted and coated in our Doncaster workshop — nothing subcontracted. 114mm to 168mm CHS depending on height Lockable cable access door with a welded reinforcing frame Internal earth stud and cable cleat Root-mounted or flange-mounted on a drilled base plate Galvanised to BS EN ISO 1461, RAL powder coat optional Made to order — dispatched in 7–10 working days. Drilled to your camera bracket pattern at no extra cost.
£285.00 ex VAT
Farm & Field Gates
Kissing Gate
Welded kissing gate enclosure and swing leaf for footpaths and permissive routes. Mobility version built to the wider clearances required for pushchairs and wheelchairs. Fully welded enclosure and leaf Self-closing gravity hinge Root-set or base-plated posts Hot dip galvanised Made to order — dispatched in 7–10 working days. Competitor lead times on this line commonly run to six weeks.
£785.00 ex VAT
Estate Fencing & Tree Protection
Estate Railing Panel
Traditional estate railing with through-drilled horizontal rails and pointed verticals, welded and finished here. Rakes and curves are made to the survey, not bent on site. Pointed vertical bars through horizontal rails Standard heights 900mm and 1200mm Root-set or base-plated posts Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£148.00 ex VAT
Estate Fencing & Tree Protection
Estate Gate
Estate-pattern gate matched to the railing run, with a braced frame and adjustable hinge set. Pedestrian and driveway widths. Welded frame with pointed verticals Adjustable hinges and drop bolt Galvanised or RAL powder coat Made to order — dispatched in 7–10 working days.
£425.00 ex VAT
Estate Fencing & Tree Protection
Tree Guard
Welded tree guard for street and car park planting, bolted in halves so it can be fitted around an established stem and removed later without cutting. Two-part bolted construction Vertical bars at 100mm centres Root-set legs Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£268.00 ex VAT
Railings & Balustrade
Vertical Bar Railing Panel
Welded vertical bar railing for boundaries and plant enclosures, made in bay widths to suit the run rather than forcing standard modules onto site. Vertical bars through horizontal rails Standard heights 1200mm and 1800mm Root-set or base-plated posts Galvanised and powder coated Made to order — dispatched in 3–4 working days.
£158.00 ex VAT
Railings & Balustrade
Bow Top Railing Panel
Bow top railing with no finger traps or foot holds — the standard answer for schools, play areas and housing schemes. Looped bow top heads, welded frame Standard heights 1000mm and 1200mm Root-set or base-plated posts Galvanised and powder coated to any RAL Made to order — dispatched in 3–4 working days.
£142.00 ex VAT
Site & Street Metalwork
Bin Store Enclosure
Welded bin store with a hinged access gate and a slatted or mesh infill, sized to the number of bins it actually has to hold. Welded frame, slatted or mesh infill Hinged gate with hasp and staple Base-plated or root-set Galvanised and powder coated to any RAL Made to order — dispatched in 7–10 working days.
£985.00 ex VAT
Site & Street Metalwork
Cycle Shelter
Fabricated cycle shelter frame with a mono-pitch roof and integral Sheffield stands. Frame, stands and fixings all made in-house. Portal frame with welded haunches Integral cycle stands Roof sheet or polycarbonate Galvanised and powder coated Made to order — dispatched in 7–10 working days.
£2,285.00 ex VAT
Site & Street Metalwork
Steel Planter
Welded steel planter with a folded top edge, drainage and an internal liner rail. Also works as a discreet hostile vehicle mitigation element when specified with a heavier base. Folded and welded plate, dressed seams Drainage holes and liner rail Galvanised and powder coated, or Corten-look finish Made to order — dispatched in 7–10 working days.
£425.00 ex VAT
Need for local authorities to your own sizes?
Send a drawing or a schedule and we'll price it against your spec — budget costs back within 48 hours.