Poles, posts and pedestals for security installers
CCTV poles, hinged service columns and intercom or reader pedestals with apertures cut to the exact footprint of the hardware you are fitting. Internal cable routes, gland plates, cabinet mounts and matching foundation cages are all fabricated here.
12 products
Bollards & Impact Protection
Anti-Ram Security Bollard
Heavy-wall section on a deep root with a reinforced base cage, specified where the bollard has a real job to do rather than a visual one. Foundation detail supplied with the order. 168mm or 219mm CHS, 8mm wall Reinforcing bar cage welded to the root 1000mm foundation depth recommended Galvanised, RAL powder coat optional Made to order — dispatched in 7–10 working days.
£142.50 ex VAT
CCTV Poles & Columns
Tubular CCTV Pole
Fabricated CCTV column with a welded cap plate, internal cable route and a lockable access door at low level. Cut, welded, blasted and coated in our Doncaster workshop — nothing subcontracted. 114mm to 168mm CHS depending on height Lockable cable access door with a welded reinforcing frame Internal earth stud and cable cleat Root-mounted or flange-mounted on a drilled base plate Galvanised to BS EN ISO 1461, RAL powder coat optional Made to order — dispatched in 7–10 working days. Drilled to your camera bracket pattern at no extra cost.
£285.00 ex VAT
CCTV Poles & Columns
Square Section CCTV Pole
Square hollow section column — flat faces make bracket and enclosure mounting far easier than a round pole, and it reads cleaner on modern buildings. 100mm to 150mm SHS depending on height Lockable cable access door, welded reinforcing frame Welded cap plate and internal earth stud Drilled to your bracket pattern on request Galvanised, RAL powder coat optional Made to order — dispatched in 7–10 working days.
£295.00 ex VAT
CCTV Poles & Columns
Hinged Raise & Lower CCTV Column
Hinged at the base so the head comes down to working height for camera service — no MEWP hire every time a lens needs cleaning. Hinge block, pivot pin and locking collar all fabricated here. Machined hinge block on a bolt-down base flange Locking collar and safety pin at the upright position Winch point welded to the shaft Galvanised throughout Made to order — dispatched in 7–10 working days.
£985.00 ex VAT
CCTV Poles & Columns
Camera Mounting Bracket
Fabricated mounting brackets for pole, wall and corner installations, drilled to the fixing centres of your camera or enclosure rather than a generic pattern. 6mm plate, fully welded gussets Cable pass-through with a grommet Drilled to your template — send the datasheet Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£68.00 ex VAT
CCTV Poles & Columns
Column Base Plate & Foundation Cage
Holding-down bolt cage and template for flange-mounted columns, made to your bolt centres so the column lands square first time. M16 or M20 holding-down bolts with plate washers Welded cage with a setting-out template Galvanised throughout Made to order — dispatched in 3–4 working days.
£96.00 ex VAT
Intercom & Reader Posts
Single Intercom Post
Steel intercom pedestal with a rear access panel and a clean cable route from the root to the device aperture. We supply the post — the electronics come from your own supplier. 150 x 150mm SHS, welded cap Lockable rear access panel Cable entry at the root, sealed grommet Supplied undrilled, or cut to your unit's template Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£195.00 ex VAT
Intercom & Reader Posts
Twin Height Intercom Post
Two apertures at car and HGV driver height on one post, so a single pedestal serves both. Apertures cut to your device footprints before coating. 150 x 150mm SHS Two device apertures, heights to your spec Full-height rear access panel Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£298.00 ex VAT
Intercom & Reader Posts
Card Reader Post
Slim pedestal for proximity and keypad readers, with an angled head face so the reader sits square to the driver's window. 100 x 100mm SHS Angled head plate, aperture to your reader Rear access panel and cable grommet Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£168.00 ex VAT
Intercom & Reader Posts
Combination Intercom & Reader Post
One post carrying an intercom, a reader and, where needed, a keypad — apertures set out on a drawing you approve before we cut. 150 x 150mm SHS Up to three device apertures Full-height rear access panel Galvanised or RAL powder coat Made to order — dispatched in 3–4 working days.
£312.00 ex VAT
Commercial Gates
Swing Gate Prepared for Automation
Swing gate built from the outset to take a motor — reinforced stiles, welded motor mounting plates, pre-cut ducting entries and a bonded earth path. Retro-fitting automation to a gate that was not designed for it is where most installs go wrong. Reinforced hanging stiles and hinge posts Welded motor plates set out to your operator Ducting entries cut and sleeved before coating Earth bonding points welded in Galvanised and powder coated Made to order — dispatched in 7–10 working days. Automation supplied and commissioned as a fitted service — call for prices, trade discounts available.
£1,685.00 ex VAT
Mesh Gates
Mesh Infill Gate — Single Leaf
Single leaf gate with a welded steel frame and mesh infill to match an existing fence line. We fabricate the frame, posts and hardware; the mesh panel is bought in as a material. Welded box frame, mesh clamped and bolted Twin-wire or 358 high-security infill Adjustable hinges and lock box Galvanised and powder coated Made to order — dispatched in 7–10 working days.
£385.00 ex VAT
Need for security installers to your own sizes?
Send a drawing or a schedule and we'll price it against your spec — budget costs back within 48 hours.